Skillnad mellan versioner av "Grove - Digital Light Sensor"

Från Karlskrona Makerspace Wiki
Hoppa till: navigering, sök
 
Rad 8: Rad 8:
 
== Port ==
 
== Port ==
 
* I2C
 
* I2C
 +
 +
== Bibliotek ==
 +
Till Arduino IDE:
 +
https://github.com/Seeed-Studio/Grove_Digital_Light_Sensor/archive/master.zip
  
 
== Exempelkod ==  
 
== Exempelkod ==  
 
=== Arduino ===
 
=== Arduino ===
 
<syntaxhighlight lang="C++" line>
 
<syntaxhighlight lang="C++" line>
 +
#include <Wire.h>
 +
#include <Digital_Light_TSL2561.h>
 +
void setup()
 +
{
 +
  Wire.begin();
 +
  Serial.begin(9600);
 +
  TSL2561.init();
 +
}
  
 +
void loop()
 +
{
 +
  Serial.print("The Light value is: ");
 +
  Serial.println(TSL2561.readVisibleLux());
 +
  delay(1000);
 +
}
 
</syntaxhighlight>
 
</syntaxhighlight>
  
 
=== Raspberry Pi ===  
 
=== Raspberry Pi ===  
 
<syntaxhighlight lang="C++" line>
 
<syntaxhighlight lang="C++" line>
 +
from time import sleep
 +
import smbus
 +
from Adafruit_I2C import Adafruit_I2C
 +
import RPi.GPIO as GPIO
 +
from smbus import SMBus
 +
 +
TSL2561_Control = 0x80
 +
TSL2561_Timing = 0x81
 +
TSL2561_Interrupt = 0x86
 +
TSL2561_Channel0L = 0x8C
 +
TSL2561_Channel0H = 0x8D
 +
TSL2561_Channel1L = 0x8E
 +
TSL2561_Channel1H = 0x8F
 +
 +
TSL2561_Address = 0x29 #device address
 +
 +
LUX_SCALE = 14 # scale by 2^14
 +
RATIO_SCALE = 9 # scale ratio by 2^9
 +
CH_SCALE = 10 # scale channel values by 2^10
 +
CHSCALE_TINT0 = 0x7517 # 322/11 * 2^CH_SCALE
 +
CHSCALE_TINT1 = 0x0fe7 # 322/81 * 2^CH_SCALE
 +
 +
K1T = 0x0040 # 0.125 * 2^RATIO_SCALE
 +
B1T = 0x01f2 # 0.0304 * 2^LUX_SCALE
 +
M1T = 0x01be # 0.0272 * 2^LUX_SCALE
 +
K2T = 0x0080 # 0.250 * 2^RATIO_SCA
 +
B2T = 0x0214 # 0.0325 * 2^LUX_SCALE
 +
M2T = 0x02d1 # 0.0440 * 2^LUX_SCALE
 +
K3T = 0x00c0 # 0.375 * 2^RATIO_SCALE
 +
B3T = 0x023f # 0.0351 * 2^LUX_SCALE
 +
M3T = 0x037b # 0.0544 * 2^LUX_SCALE
 +
K4T = 0x0100 # 0.50 * 2^RATIO_SCALE
 +
B4T = 0x0270 # 0.0381 * 2^LUX_SCALE
 +
M4T = 0x03fe # 0.0624 * 2^LUX_SCALE
 +
K5T = 0x0138 # 0.61 * 2^RATIO_SCALE
 +
B5T = 0x016f # 0.0224 * 2^LUX_SCALE
 +
M5T = 0x01fc # 0.0310 * 2^LUX_SCALE
 +
K6T = 0x019a # 0.80 * 2^RATIO_SCALE
 +
B6T = 0x00d2 # 0.0128 * 2^LUX_SCALE
 +
M6T = 0x00fb # 0.0153 * 2^LUX_SCALE
 +
K7T = 0x029a # 1.3 * 2^RATIO_SCALE
 +
B7T = 0x0018 # 0.00146 * 2^LUX_SCALE
 +
M7T = 0x0012 # 0.00112 * 2^LUX_SCALE
 +
K8T = 0x029a # 1.3 * 2^RATIO_SCALE
 +
B8T = 0x0000 # 0.000 * 2^LUX_SCALE
 +
M8T = 0x0000 # 0.000 * 2^LUX_SCALE
 +
 +
 +
 +
K1C = 0x0043 # 0.130 * 2^RATIO_SCALE
 +
B1C = 0x0204 # 0.0315 * 2^LUX_SCALE
 +
M1C = 0x01ad # 0.0262 * 2^LUX_SCALE
 +
K2C = 0x0085 # 0.260 * 2^RATIO_SCALE
 +
B2C = 0x0228 # 0.0337 * 2^LUX_SCALE
 +
M2C = 0x02c1 # 0.0430 * 2^LUX_SCALE
 +
K3C = 0x00c8 # 0.390 * 2^RATIO_SCALE
 +
B3C = 0x0253 # 0.0363 * 2^LUX_SCALE
 +
M3C = 0x0363 # 0.0529 * 2^LUX_SCALE
 +
K4C = 0x010a # 0.520 * 2^RATIO_SCALE
 +
B4C = 0x0282 # 0.0392 * 2^LUX_SCALE
 +
M4C = 0x03df # 0.0605 * 2^LUX_SCALE
 +
K5C = 0x014d # 0.65 * 2^RATIO_SCALE
 +
B5C = 0x0177 # 0.0229 * 2^LUX_SCALE
 +
M5C = 0x01dd # 0.0291 * 2^LUX_SCALE
 +
K6C = 0x019a # 0.80 * 2^RATIO_SCALE
 +
B6C = 0x0101 # 0.0157 * 2^LUX_SCALE
 +
M6C = 0x0127 # 0.0180 * 2^LUX_SCALE
 +
K7C = 0x029a # 1.3 * 2^RATIO_SCALE
 +
B7C = 0x0037 # 0.00338 * 2^LUX_SCALE
 +
M7C = 0x002b # 0.00260 * 2^LUX_SCALE
 +
K8C = 0x029a # 1.3 * 2^RATIO_SCALE
 +
B8C = 0x0000 # 0.000 * 2^LUX_SCALE
 +
M8C = 0x0000 # 0.000 * 2^LUX_SCALE
 +
 +
# bus parameters
 +
rev = GPIO.RPI_REVISION
 +
if rev == 2 or rev == 3:
 +
    bus = smbus.SMBus(1)
 +
else:
 +
    bus = smbus.SMBus(0)
 +
i2c = Adafruit_I2C(TSL2561_Address)
 +
 +
debug = False
 +
cooldown_time = 0.005 # measured in seconds
 +
packageType = 0 # 0=T package, 1=CS package
 +
gain = 0        # current gain: 0=1x, 1=16x [dynamically selected]
 +
gain_m = 1      # current gain, as multiplier
 +
timing = 2      # current integration time: 0=13.7ms, 1=101ms, 2=402ms [dynamically selected]
 +
timing_ms = 0  # current integration time, in ms
 +
channel0 = 0    # raw current value of visible+ir sensor
 +
channel1 = 0    # raw current value of ir sensor
 +
schannel0 = 0  # normalized current value of visible+ir sensor
 +
schannel1 = 0  # normalized current value of ir sensor
 +
 +
 +
def readRegister(address):
 +
    try:
 +
        byteval = i2c.readU8(address)
 +
 +
        sleep(cooldown_time)
 +
        if (debug):
 +
            print("TSL2561.readRegister: returned 0x%02X from reg 0x%02X" % (byteval, address))
 +
        return byteval
 +
    except IOError:
 +
        print("TSL2561.readRegister: error reading byte from reg 0x%02X" % address)
 +
        return -1
 +
 +
 +
def writeRegister(address, val):
 +
    try:
 +
        i2c.write8(address, val)
 +
 +
        sleep(cooldown_time)
 +
        if (debug):
 +
            print("TSL2561.writeRegister: wrote 0x%02X to reg 0x%02X" % (val, address))
 +
    except IOError:
 +
 +
        sleep(cooldown_time)
 +
        print("TSL2561.writeRegister: error writing byte to reg 0x%02X" % address)
 +
        return -1
 +
 +
def powerUp():
 +
    writeRegister(TSL2561_Control, 0x03)
 +
 +
def powerDown():
 +
    writeRegister(TSL2561_Control, 0x00)
 +
 +
def setTintAndGain():
 +
    global gain_m, timing_ms
 +
 +
    if gain == 0:
 +
        gain_m = 1
 +
    else:
 +
        gain_m = 16
 +
 +
    if timing == 0:
 +
        timing_ms = 13.7
 +
    elif timing == 1:
 +
        timing_ms = 101
 +
    else:
 +
        timing_ms = 402
 +
    writeRegister(TSL2561_Timing, timing | gain << 4)
 +
 +
def readLux():
 +
    sleep(float(timing_ms + 1) / 1000)
 +
 +
    ch0_low  = readRegister(TSL2561_Channel0L)
 +
    ch0_high = readRegister(TSL2561_Channel0H)
 +
    ch1_low  = readRegister(TSL2561_Channel1L)
 +
    ch1_high = readRegister(TSL2561_Channel1H)
 +
 +
    global channel0, channel1
 +
    channel0 = (ch0_high<<8) | ch0_low
 +
    channel1 = (ch1_high<<8) | ch1_low
 +
 +
    sleep(cooldown_time)
 +
    if debug:
 +
        print("TSL2561.readVisibleLux: channel 0 = %i, channel 1 = %i [gain=%ix, timing=%ims]" % (channel0, channel1, gain_m, timing_ms))
 +
 +
def readVisibleLux():
 +
    global timing, gain
 +
 +
    powerUp()
 +
    readLux()
 +
 +
    if channel0 < 500 and timing == 0:
 +
        timing = 1
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: too dark. Increasing integration time from 13.7ms to 101ms")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    if channel0 < 500 and timing == 1:
 +
        timing = 2
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: too dark. Increasing integration time from 101ms to 402ms")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    if channel0 < 500 and timing == 2 and gain == 0:
 +
        gain = 1
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: too dark. Setting high gain")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    if (channel0 > 20000 or channel1 > 20000) and timing == 2 and gain == 1:
 +
        gain = 0
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: enough light. Setting low gain")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    if (channel0 > 20000 or channel1 > 20000) and timing == 2:
 +
        timing = 1
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: enough light. Reducing integration time from 402ms to 101ms")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    if (channel0 > 10000 or channel1 > 10000) and timing == 1:
 +
        timing = 0
 +
        sleep(cooldown_time)
 +
        if debug:
 +
            print("TSL2561.readVisibleLux: enough light. Reducing integration time from 101ms to 13.7ms")
 +
        setTintAndGain()
 +
        readLux()
 +
 +
    powerDown()
 +
 +
    if (timing == 0 and (channel0 > 5000 or channel1 > 5000)) or (timing == 1 and (channel0 > 37000 or channel1 > 37000)) or (timing == 2 and (channel0 > 65000 or channel1 > 65000)):
 +
        # overflow
 +
        return -1
 +
 +
    return calculateLux(channel0, channel1)
 +
 +
def calculateLux(ch0, ch1):
 +
    chScale = 0
 +
    if timing == 0:  # 13.7 msec
 +
        chScale = CHSCALE_TINT0
 +
    elif timing == 1: # 101 msec
 +
        chScale = CHSCALE_TINT1;
 +
    else:          # assume no scaling
 +
        chScale = (1 << CH_SCALE)
 +
 +
    if gain == 0:
 +
        chScale = chScale << 4 # scale 1X to 16X
 +
 +
    # scale the channel values
 +
    global schannel0, schannel1
 +
    schannel0 = (ch0 * chScale) >> CH_SCALE
 +
    schannel1 = (ch1 * chScale) >> CH_SCALE
 +
 +
    ratio = 0
 +
    if schannel0 != 0:
 +
        ratio = (schannel1 << (RATIO_SCALE+1)) / schannel0
 +
    ratio = (ratio + 1) >> 1
 +
 +
    if packageType == 0: # T package
 +
        if ((ratio >= 0) and (ratio <= K1T)):
 +
            b=B1T; m=M1T;
 +
        elif (ratio <= K2T):
 +
            b=B2T; m=M2T;
 +
        elif (ratio <= K3T):
 +
            b=B3T; m=M3T;
 +
        elif (ratio <= K4T):
 +
            b=B4T; m=M4T;
 +
        elif (ratio <= K5T):
 +
            b=B5T; m=M5T;
 +
        elif (ratio <= K6T):
 +
            b=B6T; m=M6T;
 +
        elif (ratio <= K7T):
 +
            b=B7T; m=M7T;
 +
        elif (ratio > K8T):
 +
            b=B8T; m=M8T;
 +
    elif packageType == 1: # CS package
 +
        if ((ratio >= 0) and (ratio <= K1C)):
 +
            b=B1C; m=M1C;
 +
        elif (ratio <= K2C):
 +
            b=B2C; m=M2C;
 +
        elif (ratio <= K3C):
 +
            b=B3C; m=M3C;
 +
        elif (ratio <= K4C):
 +
            b=B4C; m=M4C;
 +
        elif (ratio <= K5C):
 +
            b=B5C; m=M5C;
 +
        elif (ratio <= K6C):
 +
            b=B6C; m=M6C;
 +
        elif (ratio <= K7C):
 +
            b=B7C; m=M7C;
 +
 +
    temp = ((schannel0*b)-(schannel1*m))
 +
    if temp < 0:
 +
        temp = 0;
 +
    temp += (1<<(LUX_SCALE-1))
 +
    # strip off fractional portion
 +
    lux = temp>>LUX_SCALE
 +
    sleep(cooldown_time)
 +
    if debug:
 +
        print("TSL2561.calculateLux: %i" % lux)
 +
 +
    return lux
 +
 +
def init():
 +
    powerUp()
 +
    setTintAndGain()
 +
    writeRegister(TSL2561_Interrupt, 0x00)
 +
    powerDown()
 +
 +
def main():
 +
    init()
 +
    while (True):
 +
        print("Lux: %i [Vis+IR=%i, IR=%i @ Gain=%ix, Timing=%.1fms]" % (readVisibleLux(), channel0, channel1, gain_m, timing_ms))
 +
        sleep(1)
  
 +
if __name__ == "__main__":
 +
        main()
 
</syntaxhighlight>
 
</syntaxhighlight>
  

Versionen från 26 oktober 2018 kl. 22.34

Denna modul är baserad på I2C ljus-till-digital-omvandlaren TSL2561 för att omvandla ljusintensitet till en digital signal. Olika traditionella analogljussensorer, som Grove-Light Sensor, har denna digitala modul ett valbart ljusspektrumområde på grund av dess dubbla ljuskänsliga dioder: infraröd och fullt spektrum. Vi kan växla mellan tre detekteringslägen för att ta dina avläsningar. De är infrarödläge, fullt spektrum och mänskligt synligt läge.

Kompatibilitet

  • Arduino
  • Raspberry Pi

Port

  • I2C

Bibliotek

Till Arduino IDE: https://github.com/Seeed-Studio/Grove_Digital_Light_Sensor/archive/master.zip

Exempelkod

Arduino

#include <Wire.h>
#include <Digital_Light_TSL2561.h>
void setup()
{
  Wire.begin();
  Serial.begin(9600);
  TSL2561.init();
}

void loop()
{
  Serial.print("The Light value is: ");
  Serial.println(TSL2561.readVisibleLux());
  delay(1000);
}

Raspberry Pi

from time import sleep
import smbus
from Adafruit_I2C import Adafruit_I2C
import RPi.GPIO as GPIO
from smbus import SMBus

TSL2561_Control = 0x80
TSL2561_Timing = 0x81
TSL2561_Interrupt = 0x86
TSL2561_Channel0L = 0x8C
TSL2561_Channel0H = 0x8D
TSL2561_Channel1L = 0x8E
TSL2561_Channel1H = 0x8F

TSL2561_Address = 0x29 #device address

LUX_SCALE = 14 # scale by 2^14
RATIO_SCALE = 9 # scale ratio by 2^9
CH_SCALE = 10 # scale channel values by 2^10
CHSCALE_TINT0 = 0x7517 # 322/11 * 2^CH_SCALE
CHSCALE_TINT1 = 0x0fe7 # 322/81 * 2^CH_SCALE

K1T = 0x0040 # 0.125 * 2^RATIO_SCALE
B1T = 0x01f2 # 0.0304 * 2^LUX_SCALE
M1T = 0x01be # 0.0272 * 2^LUX_SCALE
K2T = 0x0080 # 0.250 * 2^RATIO_SCA
B2T = 0x0214 # 0.0325 * 2^LUX_SCALE
M2T = 0x02d1 # 0.0440 * 2^LUX_SCALE
K3T = 0x00c0 # 0.375 * 2^RATIO_SCALE
B3T = 0x023f # 0.0351 * 2^LUX_SCALE
M3T = 0x037b # 0.0544 * 2^LUX_SCALE
K4T = 0x0100 # 0.50 * 2^RATIO_SCALE
B4T = 0x0270 # 0.0381 * 2^LUX_SCALE
M4T = 0x03fe # 0.0624 * 2^LUX_SCALE
K5T = 0x0138 # 0.61 * 2^RATIO_SCALE
B5T = 0x016f # 0.0224 * 2^LUX_SCALE
M5T = 0x01fc # 0.0310 * 2^LUX_SCALE
K6T = 0x019a # 0.80 * 2^RATIO_SCALE
B6T = 0x00d2 # 0.0128 * 2^LUX_SCALE
M6T = 0x00fb # 0.0153 * 2^LUX_SCALE
K7T = 0x029a # 1.3 * 2^RATIO_SCALE
B7T = 0x0018 # 0.00146 * 2^LUX_SCALE
M7T = 0x0012 # 0.00112 * 2^LUX_SCALE
K8T = 0x029a # 1.3 * 2^RATIO_SCALE
B8T = 0x0000 # 0.000 * 2^LUX_SCALE
M8T = 0x0000 # 0.000 * 2^LUX_SCALE



K1C = 0x0043 # 0.130 * 2^RATIO_SCALE
B1C = 0x0204 # 0.0315 * 2^LUX_SCALE
M1C = 0x01ad # 0.0262 * 2^LUX_SCALE
K2C = 0x0085 # 0.260 * 2^RATIO_SCALE
B2C = 0x0228 # 0.0337 * 2^LUX_SCALE
M2C = 0x02c1 # 0.0430 * 2^LUX_SCALE
K3C = 0x00c8 # 0.390 * 2^RATIO_SCALE
B3C = 0x0253 # 0.0363 * 2^LUX_SCALE
M3C = 0x0363 # 0.0529 * 2^LUX_SCALE
K4C = 0x010a # 0.520 * 2^RATIO_SCALE
B4C = 0x0282 # 0.0392 * 2^LUX_SCALE
M4C = 0x03df # 0.0605 * 2^LUX_SCALE
K5C = 0x014d # 0.65 * 2^RATIO_SCALE
B5C = 0x0177 # 0.0229 * 2^LUX_SCALE
M5C = 0x01dd # 0.0291 * 2^LUX_SCALE
K6C = 0x019a # 0.80 * 2^RATIO_SCALE
B6C = 0x0101 # 0.0157 * 2^LUX_SCALE
M6C = 0x0127 # 0.0180 * 2^LUX_SCALE
K7C = 0x029a # 1.3 * 2^RATIO_SCALE
B7C = 0x0037 # 0.00338 * 2^LUX_SCALE
M7C = 0x002b # 0.00260 * 2^LUX_SCALE
K8C = 0x029a # 1.3 * 2^RATIO_SCALE
B8C = 0x0000 # 0.000 * 2^LUX_SCALE
M8C = 0x0000 # 0.000 * 2^LUX_SCALE

# bus parameters
rev = GPIO.RPI_REVISION
if rev == 2 or rev == 3:
    bus = smbus.SMBus(1)
else:
    bus = smbus.SMBus(0)
i2c = Adafruit_I2C(TSL2561_Address)

debug = False
cooldown_time = 0.005 # measured in seconds
packageType = 0 # 0=T package, 1=CS package
gain = 0        # current gain: 0=1x, 1=16x [dynamically selected]
gain_m = 1      # current gain, as multiplier
timing = 2      # current integration time: 0=13.7ms, 1=101ms, 2=402ms [dynamically selected]
timing_ms = 0   # current integration time, in ms
channel0 = 0    # raw current value of visible+ir sensor
channel1 = 0    # raw current value of ir sensor
schannel0 = 0   # normalized current value of visible+ir sensor
schannel1 = 0   # normalized current value of ir sensor


def readRegister(address):
    try:
        byteval = i2c.readU8(address)

        sleep(cooldown_time)
        if (debug):
            print("TSL2561.readRegister: returned 0x%02X from reg 0x%02X" % (byteval, address))
        return byteval
    except IOError:
        print("TSL2561.readRegister: error reading byte from reg 0x%02X" % address)
        return -1


def writeRegister(address, val):
    try:
        i2c.write8(address, val)

        sleep(cooldown_time)
        if (debug):
            print("TSL2561.writeRegister: wrote 0x%02X to reg 0x%02X" % (val, address))
    except IOError:

        sleep(cooldown_time)
        print("TSL2561.writeRegister: error writing byte to reg 0x%02X" % address)
        return -1

def powerUp():
    writeRegister(TSL2561_Control, 0x03)

def powerDown():
    writeRegister(TSL2561_Control, 0x00)

def setTintAndGain():
    global gain_m, timing_ms

    if gain == 0:
        gain_m = 1
    else:
        gain_m = 16

    if timing == 0:
        timing_ms = 13.7
    elif timing == 1:
        timing_ms = 101
    else:
        timing_ms = 402
    writeRegister(TSL2561_Timing, timing | gain << 4)

def readLux():
    sleep(float(timing_ms + 1) / 1000)

    ch0_low  = readRegister(TSL2561_Channel0L)
    ch0_high = readRegister(TSL2561_Channel0H)
    ch1_low  = readRegister(TSL2561_Channel1L)
    ch1_high = readRegister(TSL2561_Channel1H)

    global channel0, channel1
    channel0 = (ch0_high<<8) | ch0_low
    channel1 = (ch1_high<<8) | ch1_low

    sleep(cooldown_time)
    if debug:
        print("TSL2561.readVisibleLux: channel 0 = %i, channel 1 = %i [gain=%ix, timing=%ims]" % (channel0, channel1, gain_m, timing_ms))

def readVisibleLux():
    global timing, gain

    powerUp()
    readLux()

    if channel0 < 500 and timing == 0:
        timing = 1
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: too dark. Increasing integration time from 13.7ms to 101ms")
        setTintAndGain()
        readLux()

    if channel0 < 500 and timing == 1:
        timing = 2
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: too dark. Increasing integration time from 101ms to 402ms")
        setTintAndGain()
        readLux()

    if channel0 < 500 and timing == 2 and gain == 0:
        gain = 1
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: too dark. Setting high gain")
        setTintAndGain()
        readLux()

    if (channel0 > 20000 or channel1 > 20000) and timing == 2 and gain == 1:
        gain = 0
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: enough light. Setting low gain")
        setTintAndGain()
        readLux()

    if (channel0 > 20000 or channel1 > 20000) and timing == 2:
        timing = 1
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: enough light. Reducing integration time from 402ms to 101ms")
        setTintAndGain()
        readLux()

    if (channel0 > 10000 or channel1 > 10000) and timing == 1:
        timing = 0
        sleep(cooldown_time)
        if debug:
            print("TSL2561.readVisibleLux: enough light. Reducing integration time from 101ms to 13.7ms")
        setTintAndGain()
        readLux()

    powerDown()

    if (timing == 0 and (channel0 > 5000 or channel1 > 5000)) or (timing == 1 and (channel0 > 37000 or channel1 > 37000)) or (timing == 2 and (channel0 > 65000 or channel1 > 65000)):
        # overflow
        return -1

    return calculateLux(channel0, channel1)

def calculateLux(ch0, ch1):
    chScale = 0
    if timing == 0:   # 13.7 msec
        chScale = CHSCALE_TINT0
    elif timing == 1: # 101 msec
        chScale = CHSCALE_TINT1;
    else:           # assume no scaling
        chScale = (1 << CH_SCALE)

    if gain == 0:
        chScale = chScale << 4 # scale 1X to 16X

    # scale the channel values
    global schannel0, schannel1
    schannel0 = (ch0 * chScale) >> CH_SCALE
    schannel1 = (ch1 * chScale) >> CH_SCALE

    ratio = 0
    if schannel0 != 0:
        ratio = (schannel1 << (RATIO_SCALE+1)) / schannel0
    ratio = (ratio + 1) >> 1

    if packageType == 0: # T package
        if ((ratio >= 0) and (ratio <= K1T)):
            b=B1T; m=M1T;
        elif (ratio <= K2T):
            b=B2T; m=M2T;
        elif (ratio <= K3T):
            b=B3T; m=M3T;
        elif (ratio <= K4T):
            b=B4T; m=M4T;
        elif (ratio <= K5T):
            b=B5T; m=M5T;
        elif (ratio <= K6T):
            b=B6T; m=M6T;
        elif (ratio <= K7T):
            b=B7T; m=M7T;
        elif (ratio > K8T):
            b=B8T; m=M8T;
    elif packageType == 1: # CS package
        if ((ratio >= 0) and (ratio <= K1C)):
            b=B1C; m=M1C;
        elif (ratio <= K2C):
            b=B2C; m=M2C;
        elif (ratio <= K3C):
            b=B3C; m=M3C;
        elif (ratio <= K4C):
            b=B4C; m=M4C;
        elif (ratio <= K5C):
            b=B5C; m=M5C;
        elif (ratio <= K6C):
            b=B6C; m=M6C;
        elif (ratio <= K7C):
            b=B7C; m=M7C;

    temp = ((schannel0*b)-(schannel1*m))
    if temp < 0:
        temp = 0;
    temp += (1<<(LUX_SCALE-1))
    # strip off fractional portion
    lux = temp>>LUX_SCALE
    sleep(cooldown_time)
    if debug:
        print("TSL2561.calculateLux: %i" % lux)

    return lux

def init():
    powerUp()
    setTintAndGain()
    writeRegister(TSL2561_Interrupt, 0x00)
    powerDown()

def main():
    init()
    while (True):
        print("Lux: %i [Vis+IR=%i, IR=%i @ Gain=%ix, Timing=%.1fms]" % (readVisibleLux(), channel0, channel1, gain_m, timing_ms))
        sleep(1)

if __name__ == "__main__":
        main()

Mer information

http://wiki.seeedstudio.com/Grove-Digital_Light_Sensor/

Hämtad från "http://karlskronamakerspace.org/wiki/index.php?title=Grove_-_Digital_Light_Sensor&oldid=1084"